Product Overview

• Chip built-in 16bit AD converter, 16-bit data output.
• I2C Digital-output of 6 or 9-axis MotionFusion data ...

Product Overview

• PH sensor module is calibrated @24 degree centigrade room temperature.Calibrated Values are: PH4= 1.5V, PH7=1.2V, ...

Product Overview

• WiFi 802.11 b/g/n Standards
• Wi-Fi Direct (P2P), soft-AP
• Integrated low power 32-bit CPU could be ...

Product specifications

• Product type: 4 X 4 keypad module
• Keypad Dimensions: 6.9 cm X 7.9 cm
• Cable dimensions: 2.0 ...

Product Overview:

• One normally closed contact and one normally open contact
• Channel: 1 channel
• Relay ...

Product Overview:

• One normally closed contact and one normally open contact
• Channel: 2 channel
• Relay ...

TURBO  9590MG  RC Car/Boat 13KG  Metal  Gear Servo

• Compatible Vehicles: Universal
• Voltage: 6V - 12V
...

• Material:Other, Color:White
• Package Contents:1 Set of Supplies ...

• Support for the arduino ide 1.0+ (osx/win/linux)
• Power via usb or ...

Product Specifications

• Typical 80dBm sensitivity.
• Up to +4dBm RF transmit power.
• 3.3 to 5 V I/O.
• PIO(Programmable Input/Output) ...

The tilt sensor is ball rolling type, NOT Mercury type. The module will output logic LOW when the module is not tilted until the threshold angle; it will output logic HIGH when it is tilted ...

• Voltage supply: 3.5V-5V
• Typical voltage supply: 5V
• Output type: analog output voltage (AO) and digital switching voltage(DO)
...

The HMC5883L is a triple-axis magnetometer compass, which uses I2C for communication. This Module consists of an on-board voltage regulator allowing you to power the module with voltages ...

PROFESSIONAL EKG-EMG CABLE WITH SNAP CONNECTOR FOR GEL ECG ELECTRODES

Interface: UART TTL.

Baud rate :  Adaptive (default),support  2400-115200.

Power supply: 5 -20 V.

Power Interface: 2.54 mm Pin header or  MICRO USB interface.

A single module can drive an 8 * 8 common cathode lattice 2.Module Operating voltage: 5V. 3.Module size: 5 cm long X 3.2 cm wide X 1.5 cm high 4.With four screws hole, aperture 3mm, by using ...

Product Overview:

• I2C interface : Fast (400kHz) I2C Interface.
• EEPROM: AT24C32 32Kbit Serial I2C.
...

Stable and reliable chipset CP2102.

USB specification 2.0 compliant with full-speed 12Mbps.

Standard USB type A male and TTL 6pin connector.

6pins for 3.3V, RST, TXD, RXD, ...

The power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board

Communication interface is a standard SPI interface

Power supply indicator and Control indicator lamp

Channel: 8 channel

Relay Operating Voltage: 5V

DC or AC signal, control, you can control the 220V AC load

Product Overview:

• One normally closed contact and one normally open contact
• Channel: 4 channel
• Relay ...

Biometric Pulse Rate or Heart Rate detecting sensor

Plug and Play type sensor

Operating Voltage: +5V or +3.3V

Current Consumption: 4mA

Inbuilt Amplification and ...

• Voltage: DC 3.3V (Do not use 5V supply), Operating Current :13-26mA
• Operating Frequency: 13.56MHz
• Supported card types: mifare1 S50, mifare1 S70, Mifare Ultralight, ...

2.54mm pin interface leads

Operating Voltage: 5V.

Long service life and stable performance

Standard interface and electronic building blocks

Widely use in Arduino ...

Incremental Encoder

Supply Voltage: 3-5V

Left/Right rotary output pulse, each circle with 20 pulse

Built-in 10k resistor

Cycles per revolution (CPR): 20

• Input voltage: 3-40V
• Output voltage: 1.5-35V(Adjustable)
• Output current: Rated current is 2A, maximum 3A
• Switching Frequency: 150KHz
• Operating ...

Onboard TTP229 capacitive touch sensor IC

Operating voltage 2.4V~5.5V.

Onboard TTP226 capacitive touch sensor IC

8 board-level status indicator

Working voltage: 2.4V - 5.5V

Advanced Pins breakout, so that the output mode and working mode ...

Onboard TTP224 capacitive touch sensor IC

4 board-level status indicator

Working voltage: 2.4V - 5.5V

Advanced Pins breakout, so that the output mode and working mode ...

Power supply voltage(VCC): 2.0, 3, 5.5 V.

Output high VOH: 0.8VCC V

Output low VOL: 0.3VCC V

Response time (touch mode) : 60 mS

Output Pin Sink Current (@ VCC = 3V, ...

Operating voltage 3.3V-5V

Outputs digital switching output (high and low level 0 and 1

Operating current (Vcc=5V): 4-8mA

Microphone sensitivity (1Khz): 52-48dB

Heating voltage: 5V ± 0.2V

Working current: 140mA

Loop voltage: 10V (maximum DC 15V)

Load resistance: 10K (adjustable)

Detection concentration range: 10-1000ppm

High Sensitivity to LPG, iso-butane, propane

Small sensitivity to alcohol, smoke

Good sensitivity to Combustible gas in a wide range

High sensitivity to Propane, Butane, ...

Power Supply: 5 Volts

Interface Type: Analog & Digital

High Sensitivity to LPG, Natural Gas, Town Gas & small sensitivity to smoke & alcohol

Power Supply: 5 Volts

Interface Type: Analog & Digital

High Sensitivity to Alcohol & small sensitivity to Benzine.

Compact, thin package (46.0 ×30.0×17.6 mm)

Low consumption current (Icc: MAX. 20 mA)

The presence of dust can be detected.

Photometry of only one pulse

Enable to ...

Power Supply： 3.3~5.5V DC

Output： 4 pin single row

Measurement Range： Humidity 20-90%RH， Temperature 0~50℃

Accuracy： Humidity +-5%RH， Temperature +-2℃

Resolution： ...

Working frequency: 2.4GHz ISM band

Modulation method: GFSK(Gaussian Frequency Shift Keying)

RF Power: 0.01mw-5mw, can modify through AT Command AT+POWER

Power: +3.3VDC ...